Is your Westinghouse refrigerator not cool enough? You don’t need to freak out. Your Westinghouse refrigerator may not be cooling for certain reasons. However, the technicians will fix it after determining the root of the issue this article, we’ll go over some of the methods they use to do it. Instead of spending more money to buy a new fridge, this article will show you how to quickly fix your current one.
8 Ways to Troubleshoot Your Westinghouse Refrigerator
1. Dirty Condenser Coils
Typically, the condenser coils lie under the refrigerator. As refrigerant runs through them, they dissipate heat. The condenser coils won’t adequately disperse heat if they are filthy. The refrigerator loses efficiency when dirt accumulates on the coils, making it work harder to cool down. The refrigerator won’t be able to maintain the right temperature if the coils are very dusty. If the condenser coils are unclean, clean them immediately. If not, check the condenser coils to see if they are dusty.
2. Malfunctioning Condenser Fan Motor
Air is drawn over the compressor and through the condenser coils by the condenser fan motor. The refrigerator won’t chill correctly if the condenser fan motor is malfunctioning. First, inspect the fan blade for obstructions to see if the fan motor is broken. Next, try manually rotating the fan motor blade. Replace the condenser fan motor if the blade cannot spin freely. Use a multimeter to check the fan motor for continuity if there are no obstacles and the fan blade spins freely.
3. Malfunctioning Evaporator Fan Motor
The air in the refrigerator and freezer compartments is circulated throughout by the evaporator fan motor, which draws air over the evaporator (cooling) coils. There may be multiple evaporator fan motors in some refrigerators. The freezer section is where the evaporator is found in refrigerators with a single evaporator. The cold air cannot circulate into the refrigerator compartment if the evaporator fan is not operating. If this happens, the refrigerator won’t be cold, but the freezer might still get cool enough. Try manually rotating the fan blade to see if the evaporator fan motor is broken. Change the fan motor if the fan blade cannot rotate properly. Substitute the motor as well if it is especially noisy. Finally, check the motor windings for continuity with a multimeter if it doesn’t run at all. The evaporator fan motor needs to be replaced if the windings are not functioning smoothly.
4. Begin Relay is Broken
The compressor is started using the start winding and the start relay. If the start relay is broken, the compressor may occasionally malfunction or not operate at all. The refrigerator won’t be cold enough as a result. Use a multimeter to check for continuity between the run and start terminal sockets on the start relay to see whether it is faulty. Replace the start relay if there is no continuity between the start and run terminal sockets. Replace the start relay as well if it smells burnt.
5. Malfunctioning Thermostat
The compressor, evaporator fan motor, and condenser fan motor all receive power from the temperature control thermostat. The refrigerant system may not function if the temperature control thermostat is malfunctioning. Rotate the thermostat from the lowest setting to the highest setting while listening for a click to detect if the thermostat is faulty. The thermostat is probably not broken if it clicks. Use a multimeter to check the thermostat for continuity if it doesn’t click. Replace the thermostat for temperature control if it loses continuity in any setting.
6. Capacitor Not Starting
The compressor starts up with a boost of power thanks to the start capacitor. The compressor might not start if the start capacitor is malfunctioning. The refrigerator won’t cool as a result. Test the start capacitor using a multimeter to see whether it is faulty. Modify he start capacitor if it is faulty.
7. Temperature Control Board
The compressor and fan motors receive voltage from the temperature control board. The temperature control board will stop supplying voltage to the cooling system if it is broken. This is not a typical occurrence, though. Control boards are frequently misdiagnosed; thus, test all of the more frequently deficient components before replacing the control board. Consider changing the temperature control board if none of the other parts are broken.
The control board receives the temperature measurement from the thermistor, which keeps track of the refrigerator’s temperature. Based on the thermistor readings, the control board controls the power going to the compressor and evaporator fan. The compressor and evaporator fan may not operate as needed if the thermistor is broken. The refrigerator won’t be cold enough as a result. Use a multimeter to test the thermistor to see whether it is broken. The temperature of the refrigerator should cause a change in the thermistor resistance. Replace the thermistor if it loses continuity or if the resistance of the thermistor does not change.
Looking For a Renowned Appliance Repair Service Provider in Naples?
If you’ve tried everything you can think of to fix your refrigerator, you’ll probably need help from experts to figure out what’s wrong and fix it.
Appliance Doctor Inc. understands that underperforming refrigerator creates significant inconvenience and stress. Our refrigerator repair technicians diagnose any complications and resolve refrigerator repairs with expertise. We also have original appliance parts in stock.
Got an appliance problem? No need to worry! Our Appliance Repair team provides top-of-the-line service and prompt same-day repair work.
Call us at 239-992-0505 (Estero/Bonita Springs), 239-936-0111 (Fort Myers), 239-540-9500 (Cape Coral), 239-434-7546 (Naples) 239-642-0505 (Marco Island), and 239-732-0111 (East Naples) or you can message us online.